7075, 7076... Whatever It Takes

  • Published on: Sunday, December 1, 2019
  • Don't know if this was worth the effort, but was in a chatty mood. Come along for the ride as I sort out a few little things on a Factory Scorpa. We'll do bad things, I promise.

    Source: https://youtu.be/AhMil-ibUTY


  • Left in The SmokeSD

    Left in The SmokeSD

     1 hours ago

    Minilathe Minilathe Minilathe

  • No Real Expert

    No Real Expert

     4 hours ago

    Check out these guys asking about an aluminum flywheel on a diesel Go kart. See 4:12 https://www.enclips.net/video/uTl6oJHvfDo

  • icbm36


     5 hours ago

    Hey Tony do you know anything about something called SMO 254?

  • Andrew Bailey

    Andrew Bailey

     5 hours ago

    Thanks for getting me hooked on these videos, now all of my ads are for welders!

  • Jonathan Gaudreault

    Jonathan Gaudreault

     7 hours ago

    You're soooo funny :') Following ! :D

  • Lyor van Vliet

    Lyor van Vliet

     17 hours ago

    Awesome episode, but when are we going to see the Maho? :)

  • Michael Lake

    Michael Lake

     1 days ago

    How to connect? I need help, custom bike shop afraid to help. Need spacers/bushings now so I can let ARP know what bolts i need made.

  • Eric Groslevin

    Eric Groslevin

     1 days ago

    old Tony, I tryed to found a way to contact you outside youtube comments, but like your face is a mistery, conyact you seem to be an AVE parcour.

    to be bref, Can you show me, show us, how you will cut lexan, acrylic, plexiglass ... I thing like anyone, this material is a challenge when come to cut a squarre hole (lets say for mounting a panel voltmeter), anything I used to cut melt the "plastic" on the path of the tool and "re-sealed" it ! awesome useless cut !

    I know, I know, old school Tony drill and hand cut then filed ... but at the time or all is going fast ... handtools are another century, even if I am not so young anymore.

    please, can you make a video about it ?

  • DmakAttack


     1 days ago

    Three words for a new project.
    trust me, you need to get one and modify it

  • Randy Smith

    Randy Smith

     1 days ago

    This Old Tony+ Please check this out !
    More people need to see these videos of Dan Combs !! PLEASE check them out. I am not putting these on for any financial gain, or anything like that I am listing a video in hopes it draws some attention to this great cop !! Please pass the link along, Thanks ! https://www.enclips.net/video/3gFimxly9F8

  • TheDanksmith


     1 days ago

    Congrats on 700K Subs! :D

  • NumerNaBis


     1 days ago

    10 fingers Yeee

  • KaiserYazawa


     1 days ago

    Your channel is perfect to watch while eating some oatmeal with hot sauce.

  • Winky's Workshop

    Winky's Workshop

     1 days ago

    I saw the router coming... and it scared me. Where did you get the ultrasonic foot beg cleaner??? Ha

  • AlloutATVing


     1 days ago

    ToT i think we need to see some surface grinder knife sharpening, never saw that done before

  • Lawrence Lentini

    Lawrence Lentini

     1 days ago

    This old Tony: This foot peg is drooping so slightly that only I would notice. Let me fix that...

    Me dailying my running parts bike: I'm missing a footpeg, half the body panels, a starter, the carb for cylinder number 2 and all the tread on the rear tire. Meh, I'll just ride it till it dies cause a new tire is more than I have in the bike...

  • Stuart Anderton

    Stuart Anderton

     2 days ago

    Hey this old tony. Can you do a video on lathing spinning tops, best design, longest spin and can I have the winning top 😁

  • Dave B

    Dave B

     2 days ago

    Why not add weld to the frame?

  • Chris Lee

    Chris Lee

     2 days ago

    Try this 👍😁 fb.com/202993593066141/posts/2860248614007279/

  • Aubrey Land

    Aubrey Land

     3 days ago

    This Old Tony, how difficult would it be to produce a tap and die set for worm threads, for use on wood?
    That felt like a run on sentence somehow...